Creating a windows 7 self updating hardware independent image
This requires the implementation of ACPI brightness methods in the system firmware. Description For any camera device that is built into the chassis of the system and has mechanically fixed direction, the firmware must provide the _PLD method and set the panel field (bits ) to the appropriate value for the panel on which the camera is mounted. Description The following Pen device level requirement must be met and verified upon integration into a system. Every system that has x HCI controller and USB3 external port should support via this port.
The following methods are required: Bit 2 of the _DOS method must be disabled so that the system firmware cannot change the brightness levels automatically. For example, "Front" indicates the camera faces the user, while "back" indicates that the camera faces away from the end user. Description Systems that support USB 3 are required to have x HCI controller(s) compliant to the x HCI debug specification. There must be at least one user accessible USB 3.0 debug port on the machine.
The details of the specifications will be shared at a later date. Description When turning the radio off, Bluetooth enabled controllers shall be powered down to its lowest supported power state and no transmission/reception shall take place. Description The following Precision Touchpad device level requirement must be met and verified upon integration into a system. Microsoft highly recommend WLAN hardware module to support at least 802.11ac 2x2 configuration/design.
* Terms: If-Implemented Description Radios that support the Microsoft-OSG Defined Bluetooth HCI Extensions must comply with the specification and pass the related HLKWLK tests. Third Party Drivers requirement for full requirement details. This includes the following: Timing for the above actions can be found in the Windows 10 WLAN Device requirements.
On turning the radio back on, the Bluetooth stack for Windows shall resume the device to D0, allowing bus drivers to restart the device. Report Rate requirement for full requirement details. In either case, the user is faced with a negative experience in their connectivity and their general system usage is disrupted.Photo Sequence must be enabled by the device and driver to: Variable Photo Sequence captures a finite number of images and supports the ability to vary the capture parameters for each of the captured images. In addition, systems that support connected standby must: NOTE: For systems that require a separate driver to handle power button presses, it is acceptable to have that driver evaluate a control method that performs a Notify() on the Control Method Power Button device instead of using the GPIO-based solution above.If implemented in Camera driver then the driver should be able to return the requested number of images, in order, each with varying capture parameters as instructed by the application. Touch requirements for full requirement details: Microsoft strongly recommends touch solutions capable of reporting 5 or more simultaneous contact points. Buffering requirement for full requirement details. Description The following Pen device level requirement must be met and verified upon integration into a system. Button Array-based Power Button Touch-first (keyboard-less) systems must: NOTE: For systems that require a separate driver to handle power button presses, it is acceptable to have that driver call the 5-Button array driver's power button event interface instead of using the GPIO-based solution above.When the pixels read out from the camera sensor can be displayed correctly without any rotation, then the camera sensor’s _PLD rotation value must be set to 0. Warning Certification for Windows Server 2016, Azure Stack, and SDDC must meet the Windows Hardware Compatibility Requirements as stated in version 1607 of documentation, must use version 1607 of the HLK (build 14393) with matching playlist and supplemental content to generate logs, and must follow policies as stated in the Windows Server Policy document.When the pixels read out from the camera sensor need to be rotated clockwise to display correctly, then the camera sensor’s _PLD rotation value must be set accordingly (‘0’ for 0°, ‘2’ for 90°, ‘4’ for 180°, and ‘6’ for 270°). All integrated Cameras must support independent streaming between different pins and different filters (cameras) according to the capabilities listed in the Profiles advertised by the device. Questions about the Azure Stack or SDDC programs or how to submit the results for solution validation should be directed to the appropriate Microsoft technical account manager or partner management contact.
Search for creating a windows 7 self updating hardware independent image:
If the camera does not support Profiles, then concurrent streaming for Photo Sequence captures a sequence of photos in response to a single photo click. Custom Gestures requirement for full requirement details. General-Purpose Input/Output (GPIO) on an System that Supports Connected Standby GPIO Controllers for pins used by Windows drivers or ASL control methods must appear as devices in the ACPI namespace.